National Manuals

The DS90C365A is a programmable LVDS transmitter designed for 18-bit flat panel display links with a transmission rate of 85 MHz. It converts 21 bits of LVCMOS/LVTTL data into four LVDS data streams and transmits a phase-locked transmit clock in parallel with the data streams over the fourth LVDS link. The transmitter can be triggered by either rising or falling edge strobe. This product is ideal for solving EMI and cable size problems associated with wide, high-speed TTL interfaces, and it supports spread spectrum clocking.

File format: PDF Size:606 KB

The data sheet introduces the DS90C385/DS90C365 +3.3V Programmable LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-85 MHz, +3.3V Programmable LVDS Transmitter 18-Bit Flat Panel Display (FPD) Link-85 MHz data sheet. The data sheet introduces the features and characteristics of the product.

File format: PDF Size:337 KB

The DS90C363B is a 3.3V programmable LVDS transmitter that converts 21 bits of CMOS/TTL data into three LVDS data streams. It supports a transmit clock frequency of 65 MHz, with a transmission rate of 455 Mbps per LVDS data channel, resulting in a data throughput of 170 Mbytes/sec. The transmitter can be programmed for rising edge or falling edge strobe mode through a dedicated pin. This product is ideal for solving EMI and cable size issues associated with wide, high-speed TTL interfaces.

File format: PDF Size:602 KB

The DS90C363A/DS90CF363A +3.3V Programmable LVDS Transmitter is a transmitter that converts 21 bits of CMOS/TTL data into three LVDS data streams. It can transmit 18 bits of RGB data and 3 bits of LCD timing and control data at a rate of 455 Mbps per LVDS data channel with a clock frequency of 65 MHz.

File format: PDF Size:222 KB

The DS90C363/DS90CF364 is a TI company's 3.3V programmable LVDS transmitter and receiver that supports 20 to 65MHz shift clock, supports programmable transmitter (DS90C363) strobe select (rising or falling edge strobe), single 3.3V power supply, and low chip set (Tx + Rx) power consumption.

File format: PDF Size:290 KB

The DS90C3202 is a 3.3V single/dual FPD-Link 10-bit color receiver is designed to be used in Liquid Crystal Display TVs, LCD Monitors, Digital TVs, and Plasma Display Panel TVs

File format: PDF Size:1564 KB

The DS90C3201 is a 3.3V single/dual FPD-Link 10-bit color transmitter designed for use in Liquid Crystal Display TVs, LCD Monitors, Digital TVs, and Plasma Display Panel TVs. The DS90C3201 is designed to interface between the digital video processor and the display device using the low-power, low-EMI LVDS (Low Voltage Differential Signaling) interface. The DS90C3201 converts up to 70 bits of LVCMOS/LVTTL data into ten LVDS data streams. The transmitter can be programmed clocking data with rising edge or falling edge clock. Optional two-wire serial programming allows fine tuning in development and production environments. At a transmitted clock frequency of 135 MHz, 70 bits of LVCMOS/LVTTL data are transmitted at an effective rate of 945 Mbps per LVDS channel. Using a 135 MHz clock, the data throughput is 9.45 Gbit/s (945 Mbytes/s). This allows the dual 10-bit LVDS Transmitter to support HDTV resolutions.

File format: PDF Size:478 KB

The DS90C2501 is a highly integrated scaling IC with LVDS transmitter with a scaled resolution up to SXGA+ for single pixel input.

File format: PDF Size:627 KB

The DS90C032B is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology.

File format: PDF Size:163 KB

The DS90C032 is a low power, high speed, quad channel LVDS receiver from Texas Instruments.

File format: PDF Size:218 KB

The DS90C031B is a quad CMOS differential line driver designed for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90C031B accepts TTL/CMOS input levels and translates them to low voltage (350 mV) differential output signals. In addition the driver supports a TRI-STATE® function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra low idle power state of 11 mW typical. In addition, the DS90C031B provides power-off high impedance LVDS outputs. This feature assures minimal loading effect on the LVDS bus lines when VCC is not present. The DS90C031B and companion line receiver (DS90C032B) provide a new alternative to high power pseudo-ECL devices for high speed point-to-point interface applications.

File format: PDF Size:257 KB

The DS90C031 is a quad CMOS differential line driver designed by National Semiconductor Corporation for applications requiring ultra low power dissipation and high data rates. The device is designed to support data rates in excess of 155.5 Mbps (77.7 MHz) utilizing Low Voltage Differential Signaling (LVDS) technology. The DS90C031 accepts TTL/CMOS input levels and translates them to low voltage (350 mV) differential output signals. In addition, the driver supports a TRI-STATE® function that may be used to disable the output stage, disabling the load current, and thus dropping the device to an ultra low idle power state of 11 mW typical.

File format: PDF Size:273 KB

File format: PDF Size:0 KB

The COP87L88RG is a member of the COP8TM OTP microcontroller family with 32 Kbytes of program memory. It is pin and software compatible to the mask ROM COP888GG product family.

File format: PDF Size:446 KB

COP87L88KG 8-bit OTP microcontroller with UART and Three Multi-Function Timers

File format: PDF Size:452 KB

The COP87L88KG OTP microcontroller is a member of the COP8TM feature family using an 8-bit core architecture. It is pin and software compatible to the mask ROM COP888KG product family.

File format: PDF Size:452 KB

COP87L88GG OTP microcontroller is an 8-bit one-time programmable (OTP) microcontroller with UART and three multi-function timers

File format: PDF Size:448 KB

COP87L88GD/RD OTP (One Time Programmable) Family microcontrollers are highly integratet COP8™ Fea- ture core devices with 16k or 32k memory and advanced features including an A/D Converter

File format: PDF Size:433 KB

The COP87L88GD/RD OTP (One Time Programmable) Family microcontrollers are highly integrated COP8™ Feature core devices with 16k or 32k memory and advanced features including an A/D Converter. These multi-chip CMOS devices are suited for applications requiring a full featured controller with an 8-bit A/D converter, and as pre-production devices for a masked ROM design. Pin and software compatible 16k ROM versions are available (COP888GD), as well as a range of COP8 software and hardware development tools. Family features include an 8-bit memory mapped architecture, 10 MHz CKI (-XE = crystal oscillator) with 1µs instruction cycle, three multi-function 16-bit timer/counters, MICROWIRE/PLUS™ serial I/O, one 8-bit/8-channel A/D converter with prescaler and both differential and single ended modes, two power saving HALT/IDLE modes, MIWU, idle timer, high current outputs, software selectable I/O options, WATCHDOG™ timer and Clock Monitor, 2.7V to 5.5V operation, program code security, and 44 pin package.

File format: PDF Size:433 KB

COP87L88EK/RK Family 8-Bit CMOS OTP Microcontrollers with 8k or 32k Memory, Comparator, and Single-slope A/D Capability

File format: PDF Size:526 KB