ON Manuals (Industrial)
ON Semiconductor MUN5111T1 Series handbook
The MUN5111T1 series of bias resistor transistors is a new family of digital transistors designed to replace a single device and its external resistor bias network. The device is housed in the SC-70/SOT-323 package which is designed for low power surface mount applications.
File format: PDF Size:143 KB
ON Semiconductor MC34063A MC33063A handbook
MC34063A/D is a monolithic control circuit for DC-to-DC converters. It includes internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch.
File format: PDF Size:154 KB
ON Semiconductor NTLJS3113P handbook
File format: PDF Size:0 KB
ON Semiconductor NCP1450A handbook
The NCP1450A is a PWM step-up DC-DC switching controller produced by Semiconductor Components Industries, LLC. It is designed to power portable equipment from one or two cells battery packs. It features high efficiency, low start-up voltage, wide operating voltage range, etc.
File format: PDF Size:208 KB
ON Semiconductor NCP1030 NCP1031 handbook
NCP1030 and NCP1031 are monolithic switching regulators with on-chip Power Switch and Startup Circuits.
File format: PDF Size:145 KB
ON Semiconductor MMSZ5221ET1 Series handbook
The document introduces the MMSZ5221ET1 series preferred device Zener voltage regulators 500 mW SOD−123 surface mount
File format: PDF Size:77 KB
ON Semiconductor MCR100 Series handbook
MCR100 series SCRs are PNPN devices designed for high-volume, line-powered consumer applications such as relay and lamp drivers, small motor controls, gate drivers for larger thyristors, and sensing and detection circuits. Supplied in an inexpensive plastic TO-226AA package which is readily adaptable for use in automatic insertion equipment.
File format: PDF Size:68 KB
ON Semiconductor MC33375 Series handbook
The MC33375 series is a micro-power low dropout voltage regulator with a very low quiescent current and the ability to supply output currents up to 300mA.
File format: PDF Size:154 KB
ON Semiconductor MC14066B handbook
The MC14066B/D is a quad bilateral switch capable of controlling either digital or analog signals. It is useful in signal gating, chopper, modulator, demodulator and CMOS logic implementation. It is designed to be pin–for–pin compatible with the MC14016B, but has much lower ON resistance. Input voltage swings as large as the full supply voltage can be controlled via each independent control input.
File format: PDF Size:280 KB
ON Semiconductor MBR140SFT1 handbook
MBR140SFT1/D MBR140SFT1 Surface Mount Schottky Power Rectifier Plastic SOD-123 Package
File format: PDF Size:72 KB
ON Semiconductor NTLTD7900ZR2 handbook
This document introduces the NTLTD7900ZR2 Power MOSFET, which is a logic level N-channel Micro8 Leadless EZFETs™ power MOSFET with monolithic back-to-back Zener diode protection. This MOSFET features ultra low RDS(on) and true logic level performance. It is designed for low voltage, high speed switching applications that require high power efficiency and extended battery life. Typical applications include DC-DC converters, and power management in portable and battery powered products such as computers, printers, cellular and cordless phones.
File format: PDF Size:170 KB
ON SEMICONDUCTOR NCP302 NCP303 handbook
The NCP302 and NCP303 series are second generation ultra-low current voltage detectors that contain a programmable time delay generator. These devices are specifically designed for use as reset controllers in portable microprocessor based systems where extended battery life is paramount. Each series features a highly accurate undervoltage detector with hysteresis and an externally programmable time delay generator. This combination of features prevents erratic system reset operation. The NCP302 series consists of complementary output devices that are available with either an active high or active low reset. The NCP303 series has an open drain N-Channel output with an active low reset output.
File format: PDF Size:188 KB
ON Semiconductor NCP1800 handbook
File format: PDF Size:98 KB
ON Semiconductor SN74LS365A SN74LS367A SN74LS368A DATA SHEET
These devices are high speed hex buffers with 3-state outputs. They are organized as single 6-bit or 2-bit/4-bit, with inverting or non-inverting data (D) paths. The outputs are designed to drive 15 TTL Unit Loads or 60 Low Power Schottky loads when the Enable (E) is LOW. When the Output Enable (E) is HIGH, the outputs are forced to a high impedance “off” state. If the outputs of the 3-state devices are tied together, all but one device must be in the high impedance state to avoid high currents that would exceed the maximum ratings. Designers should ensure that Output Enable signals to 3-state devices whose outputs are tied together are designed so there is no overlap.
File format: PDF Size:95 KB
ON Semiconductor MC34071/2/4/A MC33071/2/4/A DATA SHEET
The MC33071/72/74, MC34071/72/74 series are single-chip operational amplifiers using high-quality bipolar fabrication technology and innovative design concepts.
File format: PDF Size:249 KB
ON Semiconductor MC14569B handbook
The MC14569B is a programmable divide-by-N dual 4-bit binary or BCD down counter constructed with MOS P-channel and N-channel enhancement mode devices (complementary MOS) in a monolithic structure.
File format: PDF Size:291 KB
ON Semiconductor NCP1117 NCV1117 handbook
NCP1117, NCV1117 1.0A Low-Dropout Positive Fixed and Adjustable Voltage Regulators
File format: PDF Size:144 KB
ON Semiconductor EMZ1DXV6T1 EMZ1DXV6T5 handbook
This document describes the features and characteristics of the EMZ1DXV6T1 and EMZ1DXV6T5 dual general purpose transistors. They are NPN/PNP complementary transistors designed for general purpose amplifier applications. The transistors are housed in the SOT-563 package, which is designed for low power surface mount applications.
File format: PDF Size:55 KB
ON Semiconductor TLV431A TLV431B handbook
The TLV431A/D series of low voltage precision adjustable shunt regulators are programmable over a wide voltage range of 1.24V to 16V. The TLV431A series features a guaranteed reference accuracy of ±1.0% at 25°C and ±2.0% over the entire industrial temperature range of −40°C to 85°C. For TLV431B series, the accuracy is even higher, it’s ±0.5% and ±1.0% respectively. These devices exhibit a sharp low current turn−on characteristic with a low dynamic impedance of 0.20 Ω over an operating current range of 100μA to 20mA. This combination of features makes this series an excellent replacement for zener diodes in numerous applications circuits that require a precise reference voltage. When combined with an optocoupler, the TLV431A/B can be used as an error amplifier for controlling the feedback loop in isolated low output voltage (3.0 V to 3.3 V) switching power supplies. These devices are available in economical TO−92−3 and micro size TSOP−5 and SOT−23−3 packages.
File format: PDF Size:187 KB