Industrial Manuals
UNITRODE UC5602 DATA SHEET
The UC5602 is a 18-line active termination device for SCSI (Small Computer Systems Interface) parallel bus. It meets SCSI and SCSI-2 standards. It has 10pF channel capacitance, logic command disconnects all termination lines, low supply current, trimmed regulator for accurate termination current, current limit and thermal shutdown protection, 110 Ohm termination and meets SCSI hot plugging.
File format: PDF Size:380 KB
ATMEL ATmega169V ATmega169 Preliminary
This chip is a high-performance low-power AVR® 8-bit microcontroller
File format: PDF Size:3315 KB
LUMIDRIVES Product Overview MicroDriver 16 VariLED ~ Dimmable LED Driver
MicroDriver 16 VariLED is a LED driver from LumiDrives. It can drive high power 1W or 3W LEDs, supporting a maximum of 8 3W LEDs or 16 1W LEDs, with a maximum output current of 350mA or 700mA. It supports 0-10V dimming or dimming with a remote potentiometer.
File format: PDF Size:510 KB
Astrodyne PMK150E series DATA SHEET
The Astrodyne PMK150E series is a 150 Watt Enclosed Switching Power Supply with PFC. It features universal 90-264VAC input, 5VDC to 48VDC outputs, 3000VAC Input to Output Isolation and Active Power Factor Correction.
File format: PDF Size:512 KB
MOELLER Type: MFD TP12 PT A Article No.: 106042 Sales text E/A MFD 24VDC Trans. 2E x PT100
This document describes a 24VDC MFD temperature sensor with 2 PT100 inputs and 4 transistor outputs. It is suitable for MFD-CP8 devices and can have a set temperature range.
File format: PDF Size:509 KB
DENSITRON OLED DISPLAY MODULE Application Notes PRODUCT NUMBER DD-32645C-1A with EVK board
File format: PDF Size:0 KB
FUJITSU ASSP Dual Serial Input PLL Frequency Synthesizer MB15F74UV
The Fujitsu MB15F74UV is a serial input Phase Locked Loop (PLL) frequency synthesizer with a 4000 MHz and a 2000 MHz prescalers. It uses the BiCMOS process, with a typical supply current of 9.0 mA at 3.0 V. The supply voltage range is from 2.7 V to 3.6 V. It features high frequency operation, low power supply voltage, ultra low power supply current, selectable charge pump current, and direct power saving function.
File format: PDF Size:232 KB
NORITAKE-ITRON Dot Graphic VFD Module GU180x32D-K610A4
GU180x32D-K610A4 is a Dot Graphic VFD Module produced by Noritake Itron. It has a power supply voltage range of 4.5-5.25V, a working current of -350mA and a maximum display area of 79.05x13.95mm. The brightness is 1000cd/m2.
File format: PDF Size:219 KB
UNITRODE UCC5617 DATA SHEET
UCC5617 is a SCSI (Small Computers Systems Interface) parallel bus 18-line active terminator produced by Unitrode. This terminator is pin-compatible with UC5609, and is ideal for high-performance 5V SCSI systems with an input voltage of 4.0-5.25V. The supply current is only 50mA during disconnection, making the IC attractive for lower powered systems. The UCC5617 is designed with a low channel capacitance of 2pF, which eliminates the effects of disconnected terminators at intermediate points on the bus on signal integrity. When all termination lines are actively negated, the power amplifier output stage of the UCC5617 can source full termination current and sink active negation current. Like all Unitrode terminators, the UCC5617 is completely hot pluggable and appears as high impedance at the terminating channels with TRMPWR = 0V or open. Internal circuit trimming is used to first trim the 110 impedance, and then most importantly, to trim the output current as close to the maximum SCSI-3 specification as possible, which maximizes noise margin in fast SCSI operation. This device is offered in low thermal resistance versions of the industry standard 28-pin wide body SOIC.
File format: PDF Size:255 KB
UNITRODE UC5601 DATA SHEET
The UC5601 is an active terminator that complies with the SCSI and SCSI-2 standards. It provides precise resistive pull-up to a 2.9V reference voltage for all 18 lines in a Small Computer Systems Interface (SCSI) bus cable. The device features a disconnect function that, upon a logic command, disconnects all terminating resistors and turns off the regulator, greatly reducing standby power. Other features include negative clamping on all signal lines, 20mA of active negation sink current capability, regulator current limiting, and thermal shutdown protection.
File format: PDF Size:297 KB
TEXAS INSTRUMENTS SN65LBC170 SN75LBC170 handbookhandbook
The SN65LBC170 and SN75LBC170 are monolithic integrated circuits designed for bidirectional data communication on multipoint bus-transmission lines. Potential applications include serial or parallel data transmission, cabled peripheral buses with twin axial, ribbon, or twisted-pair cabling. These devices are suitable for FAST-20 SCSI and can transmit or receive data pulses as short as 25 ns, with skew less than 3 ns. These devices combine three 3-state differential line drivers and three differential input line receivers, all of which operate from a single 5-V power supply. The driver differential outputs and the receiver differential inputs are connected internally to form three differential input/output (I/O) bus ports that are designed to offer minimum loading to the bus whenever the
File format: PDF Size:510 KB
WALTHER IEC 309-1 AND 309-2 PIN AND SLEEVE DEVICES DIN EN ISO 9001 Certificate Registration No. 4678-01 North American IEC309-1 309-2 Pin Sleeve International IEC30
F. Walther Electric Corporation is an international company committed to serving customers around the world with innovative plug and receptacle systems.
File format: PDF Size:2035 KB
TEXAS INSTRUMENTS SN75ALS170 SN75ALS170A handbook
The SN75ALS170 and SN75ALS170A triple differential bus transceivers are monolithic integrated circuits designed for bidirectional data communication on multipoint bus transmission lines. It is designed for balanced transmission lines and the driver meets ANSI Standards EIA/TIA-422-B and RS-485 and both the driver and receiver meet ITU Recommendation V.11. The SN75ALS170A is designed for FAST-20 SCSI and can transmit or receive data pulses as short as 30 ns with a maximum skew of 5 ns. The SN75ALS170 and SN75ALS170A provide three bidirectional transceivers, using high-performance low-power Schottky circuitry, designed for multipoint transmission on long bus lines in noisy environments.
File format: PDF Size:572 KB
DENSITRON TFT Evaluation Kit User manual(1)
This manual contains the instructions on setting up and using the Densitron Kyocera TFT evaluation kit. The evaluation kit contains: - 1 x Kyocera TCG057VG1AC 5.7” TFT panel o Anti glare treatment o (640 x R.G.B) x 480 dots o COG LCD with single U shaped CFL Backlight. o Recommended inverter TDK CXA-L0612A-VJL o Dimensions: 144.0 x 104.8 x 13.0 mm o
File format: PDF Size:1732 KB
EVERBOUQUET MC4002A7-SERIES
This document is the specification of MC4002A7-SERIES, which details the characteristics and parameters of the product
File format: PDF Size:591 KB
UNITRODE UCC5618 DATA SHEET
UCC5618 is a 18-line SCSI terminator produced by Unitrode. It supports SCSI, SCSI-2, SCSI-3, SPI and FAST-20 standards. It has a power supply current of only 50µA when disconnected, and a channel capacitance of 2pF.
File format: PDF Size:426 KB
MAXIM DS2714 handbook
The DS2714 is ideal for standalone charging of 1 to 4 AA or AAA NiMH “loose” cells. NiCd cells can also be charged. Temperature, voltage and charge time are monitored to provide proper fast charging control algorithms for Nickel Metal Hydride (NiMH) batteries. Battery tests are included to detect defective or inappropriate cells such as Alkaline primary batteries. The DS2714 supports a parallel charging topology, with independent monitoring and control of each cell.
File format: PDF Size:424 KB
TERRY TOOL Tool Clips Closed Type
Terry Tool Clips are produced in high quality spring steel. They are produced according to industrial and professional users' demands but are also frequently used in the d-i-y sector.
File format: PDF Size:65 KB
PANDUIT COUGAR LS9 Hand-Held Thermal Transfer Printer Accessories
COUGAR™ LS9 Hand-Held Thermal Transfer Printer is an affordable and powerful printer that increases labeling productivity. The rugged printer design meets the demanding requirements of electrical and network users. With its ability to print on a wide variety of continuous industrial label materials for wire/cable marking, component labeling, and safety/facility identification, the COUGAR™ LS9 Printer is ideal for use in the field. Labels are provided in fast loading P1™ Label Cassettes that each contain an integrated memory device for automatic formatting, recall of last legend used and number of labels remaining in the cassette. A partial cut feature provides the flexibility to choose tear-apart strips of labels for quicker installation. The COUGAR™ LS9 Printer is part of a complete line of identification solutions from PANDUIT, which also includes the PANTHER™ LS8E Hand-Held Thermal Transfer Printer with revolutionary label cut-to-length functionality.
File format: PDF Size:974 KB
HITACHI CUSTOMER S ACCEPTANCE SPECIFICATIONS
This is a technical requirement for a backlight inverter for cold cathode fluorescent lamp, the model is INVC817, which is suitable for K-C160T3E54 lamp and LMG5278 LCD module.
File format: PDF Size:105 KB