National Manuals

The CP3BT10 is a reprogrammable connectivity processor with Bluetooth® and USB interfaces from National Semiconductor Corporation. It can be used for embedded Bluetooth applications. The processor integrates a powerful RISC core, SRAM and Flash memory, which provides high computing bandwidth. It also integrates communication peripherals such as Bluetooth Lower Link Controller, USB, ACCESS.bus, Microwire/SPI, UART and Advanced Audio Interface (AAI), which provides high I/O bandwidth. In addition, the processor integrates DMA controller, CVSD/PCM conversion module, Timing and Watchdog Unit, Versatile Timer Unit, Multi-Function Timer and Multi-Input Wakeup.

File format: PDF Size:3329 KB

The USBN9603/4 are integrated USB Node controllers with enhanced DMA support. They are compatible with USB specification versions 1.0 and 1.1, and are advanced versions of the USBN9602. The devices integrate the required USB transceiver, a 3.3V regulator, a Serial Interface Engine (SIE), USB endpoint (EP) FIFOs, a versatile 8-bit parallel interface, a clock generator, and a MICROWIRE/PLUS™ interface. Seven endpoint pipes are supported, including one for the mandatory control endpoint and six for interrupt, bulk, and isochronous endpoints. Each endpoint pipe has a dedicated FIFO, with 8 bytes for the control endpoint and 64 bytes for the other endpoints. The 8-bit parallel interface supports multiplexed and non-multiplexed style CPU address/data buses. A programmable interrupt output scheme allows device configuration for different interrupt signaling requirements.

File format: PDF Size:582 KB

The DS55113–DS75113 dual differential line drivers with TRI-STATE outputs are designed to provide all the features of the DS55114–DS75114 line drivers with the added feature of driver output controls.

File format: PDF Size:202 KB

The LM3410 is a high frequency constant current LED driver from TI. It features a high switching frequency (525kHz or 1.6MHz), low standby current, small package size and high efficiency. LM3410 is suitable for applications such as LED backlight, LiIon backlight OLED and HB LED driver, handheld devices and LED flash driver.

File format: PDF Size:726 KB

The MM5483 is a liquid crystal display driver chip that can drive up to 31 segments of LCD and can be cascaded to increase this number. This chip is also capable of driving a 41⁄2-digit 7-segment display with minimal interface between the display and the data source. The MM5483 stores the display data in latches after it is latched in, and holds the data until another load pulse is received.

File format: PDF Size:173 KB

The LM4755 is a stereo audio amplifier from National Semiconductor that can output 11W per channel at 4Ω and 7W per channel at 8Ω using a single 24V supply.

File format: PDF Size:531 KB

The LMH6514 is a high performance, digitally controlled variable gain amplifier (DVGA). It combines precision gain control with a low noise, ultra-linear, differential amplifier. The LMH6514 drives a high performance ADC in a broad range of mixed signal and digital communication applications such as mobile radio and cellular base stations where auto- matic gain control (AGC) is required to increase system dy- namic range. When used in conjunction with a high speed ADC, system dynamic range can be extended by up to 42 dB. The LMH6514 has a differential input and output allowing large signal swings on a single 5V supply. It is designed to accept signals from RF elements and maintain a terminated impedance environment. The input impedance is 200Ω re- sistive. The output impedance is either 200Ω or 400Ω and is user selectable. A unique internal architecture allows use with both single ended and differential input signals. Input signals to the LMH6514 are scaled by a highly linear, digitally controlled attenuator with seven accurate 6 dB steps. The attenuator output provides the input signal for a high gain, ultra linear differential transconductor. The transconductor differential output current can be converted into a voltage by using the on-chip 200Ω or 400Ω loads. The transconductance gain is 0.1 Amp/Volt resulting in a maximum voltage gain of +32 dB when driving a 200

File format: PDF Size:530 KB

The DS10CP154A is a 1.5 Gbps 4x4 LVDS crosspoint switch optimized for high-speed signal routing and switching over FR-4 printed circuit board backplanes and balanced cables. Fully differential signal paths ensure exceptional signal integrity and noise immunity. The non-blocking architecture allows connections of any input to any output or outputs. The switch configuration can be accomplished via external pins or the System Management Bus (SMBus) interface. In addition, the SMBus circuitry enables the loss of signal (LOS) monitors that can inform a system of the presence of an open inputs condition (e.g. disconnected cable). Wide input common mode range allows the switch to accept signals with LVDS, CML and LVPECL levels; the output levels are LVDS. A very small package footprint requires a minimal space on the board while the flow-through pinout allows easy board layout. Each differential input and output is internally terminated with a 100Ω resistor to lower return losses, reduce component count and further minimize board space.

File format: PDF Size:335 KB

The LMX2531 is a low power, high performance frequency synthesizer system which includes a fully integrated delta- sigma PLL and VCO with fully integrated tank circuit. The third and fourth poles are also integrated and also adjustable. Also included are integrated ultra-low noise and high precision LDOs for the PLL and VCO which give higher supply noise immunity and also more consistent performance. When com- bined with a high quality reference oscillator, the LMX2531 generates very stable, low noise local oscillator signals for up and down conversion in wireless communication devices. The LMX2531 is a monolithic integrated circuit, fabricated in an advanced BiCMOS process. There are several different versions of this product in order to accomodate different fre- quency bands. Device programming is facilitated using a three-wire MICROWIRE Interface that can operate down to 1.8 volts. Supply voltage range is 2.8 to 3.2 Volts. The LMX2531 is available in a 36 pin 6x6x0.8 mm Lead-Free Leadless Lead-frame Package (LLP).

File format: PDF Size:632 KB

This document provides an overview of the features and functions of the DS90C383B +3.3V Programmable LVDS Transmitter 24-Bit Flat Panel Display (FPD) Link-65 MHz.

File format: PDF Size:262 KB

The LM3355 is a CMOS switched capacitor DC/DC converter that produces a regulated output voltage by automatically stepping up (boost) or stepping down (buck) the input voltage. It accepts an input voltage between 2.5V and 5.5V. The LM3355 is available with a standard output voltage of 4.1V (ideal for white LED applications).

File format: PDF Size:210 KB

This document introduces the basic functions and features of LP3855-ADJ 1.5A fast response ultra low dropout linear regulator. The regulator operates from a +2.5V to +7.0V input supply and features ultra low dropout, fast response, and low quiescent current, making it suitable for low voltage microprocessor applications.

File format: PDF Size:329 KB

The LM96000 hardware monitor has an SMBus 2.0-compatible two-wire digital interface. Using an 8-bit Sigma-Delta ADC, the LM96000 measures: - the temperature of two remote diode-connected transistors as well as its own die - the VCCP, 2.5V, 3.3VSBY, 5.0V, and 12V supplies (internal scaling resistors). To set fan speed, the LM96000 has three PWM outputs that are each controlled by one of three temperature zones. High and low PWM frequency ranges are supported. The LM96000 includes a digital filter that can be invoked to smooth temperature readings for better control of fan speed. The LM96000 has four tachometer inputs to measure fan speed. Limit and status registers for all measured values are included.

File format: PDF Size:803 KB

File format: PDF Size:0 KB

The LM4880 is a dual audio power amplifier capable of delivering typically 250mW per channel of continuous average power to an 8Ω load with 0.1% THD+N using a 5V power supply. It features low-power consumption shutdown mode and internal thermal shutdown protection mechanism.

File format: PDF Size:444 KB

The LM3916 is an integrated circuit that senses analog voltage levels and drives ten LEDs, LCDs or vacuum fluorescent displays, providing an electronic version of the popular VU meter.

File format: PDF Size:973 KB

The ADC08100 is a low-power, 8-bit, monolithic analog-to- digital converter with an on-chip track-and-hold circuit. Optimized for low cost, low power, small size and ease of use, this product operates at conversion rates of 20 MSPS to 100 MSPS with outstanding dynamic performance over its full operating range while consuming just 1.3 mW per MHz of clock frequency. That’s just 130 mW of power at 100 MSPS. Raising the PD pin puts the ADC08100 into a Power Down mode where it consumes just 1 mW. The unique architecture achieves 7.4 Effective Bits with 41 MHz input frequency. The excellent DC and AC charac- teristics of this device, together with its low power consump- tion and single +3V supply operation, make it ideally suited for many imaging and communications applications, includ- ing use in portable equipment. Furthermore, the ADC08100 is resistant to latch-up and the outputs are short-circuit proof. The top and bottom of the ADC08100’s reference ladder are available for connections, enabling a wide range of input possibilities. The digital outputs are TTL/CMOS compatible with a separate output power supply pin to support interfac- ing with 3V or 2.5V logic. The digital inputs (CLK and PD) are TTL/CMOS compatible. The ADC08100 is offered in a 24-lead plastic package (TSSOP) and is specified over the industrial temperature range of −40˚C to +85˚C. An evaluation board is available to assist in evaluating device performance.

File format: PDF Size:554 KB

LMH0346 3 Gbps HD/SD SDI Reclocker is a chip that can re-time digital video data. It conforms to the SMPTE 424M, SMPTE 292M, and SMPTE 259M (C) standards. The chip operates at data rates of 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.967 Gbps, and 2.97 Gbps. LMH0346 supports DVB-ASI operation at 270 Mbps. LMH0346 automatically detects the incoming data rate and adjusts itself to retime the incoming data to suppress accumulated jitter. LMH0346 also recovers the serial data-rate clock and optionally provides it as an output. LMH0346 has two differential serial data outputs, the second output can be selected as a low-jitter, data-rate clock output. Controls and indicators are: serial clock or second serial data output select, manual rate select input, SD/HD rate indicator output, lock detect output, auto/manual data bypass and output mute. The serial data inputs, outputs, and serial clock outputs are differential LVPECL compatible. The CML serial data and serial clock outputs are suitable for driving 100 Ω differentially terminated networks. The control logic inputs and outputs are LVCMOS compatible. LMH0346 is powered from a single 3.3V supply. Typical power dissipation is 370 mW. The device is available in two space–saving packages: a 6.5 X 4.4 mm 20-pin e-TSSOP and an even more space–efficient 5 X 4 mm 24-pin LLP package.

File format: PDF Size:340 KB

The LM4872 is a 1-watt audio power amplifier in a micro SMD package. It is bridge-connected and capable of delivering 1 watt of continuous average power to an 8Ω load with less than 0.2% total harmonic distortion (THD) from a 5V power supply. The LM4872 is designed for low-power portable applications and does not require output coupling capacitors or bootstrap capacitors. It features an externally controlled low-power consumption shutdown mode and internal thermal shutdown protection mechanism.

File format: PDF Size:466 KB

The LM2751 is a 2X, 1.5X regulated switched capacitor white LED driver. It offers 4.5V and 5.0V regulated output voltage options and provides up to 150mA of output current in the 2.8V to 5.5V input voltage range, requiring only four low-cost ceramic capacitors. It provides excellent efficiency without the use of an inductor by operating the charge pump in a gain of 3/2 or 2. The proper gain for maintaining regulation is chosen so that efficiency is maximized over the input voltage range. The LM2751 uses constant frequency pre-regulation to minimize conducted noise on the input and provide a predictable switching frequency. The switching frequency is programmable to 725kHz, 300kHz, 37kHz, or 9.5kHz. The LM2751 is available in a 10-pin Leadless Leadframe No-Pullback package: LLP-10.

File format: PDF Size:954 KB