intersil Manuals

The AD590 is an integrated-circuit temperature transducer that produces an output current proportional to absolute temperature. It features linear current output, a wide temperature range, a two-terminal device with voltage input and current output, a wide power supply range, sensor isolation from the case, and low cost.

File format: PDF Size:99 KB

82C88 is a CMOS bus controller produced by Intersil. It is compatible with Bipolar 8288 and is compatible with 80C86/80C88, 80186/80188, 8086/8088, 8089. 82C88 provides three-state command outputs, has bipolar drive capability, uses scaled SAJI IV CMOS process, single 5V power supply, and low power operation.

File format: PDF Size:245 KB

The ISL6571 is a MOSFET driver and synchronous half-bridge switch from Intersil that can implement synchronous rectifier buck switching regulators. The ISL6571 can replace two power MOSFETs, a Schottky diode, two gate drivers and synchronous control circuitry. ISL6571's main application ranges are high-density power conversion circuits, including multi-phase topology computer microprocessor core power regulators, ASIC and memory array regulators, etc. Another useful feature of the ISL6571 is the compatibility with three-state input control: if the input is open, the PWM input will turn off both output drives. The ISL6571 operates in continuous conduction mode to reduce EMI constraints and enable high bandwidth operation.

File format: PDF Size:369 KB

The ISL6406, ISL6426 is an adjustable frequency, synchronous buck switching regulator optimized for generating lower voltages for the distributed DC-DC architectures. The ISL6406 offers an adjustable output voltage, while the ISL6426 provides a fixed 1.8V output. Designed to drive N-Channel MOSFETs in synchronous buck topology, the ISL6406, ISL6426 integrates the control, output adjustment and protection functions into a single package. The ISL6406, ISL6426 provides simple, single feedback loop, voltage-mode control with fast transient response. The output voltage can be precisely regulated to as low as 0.8V. The error amplifier features a 15MHz gain-bandwidth product and 6V/µs slew rate which enables high converter bandwidth for fast transient performance. Protection from overcurrent conditions is provided by monitoring the rDS(ON) of the upper MOSFET to inhibit PWM operation appropriately. This approach simplifies the implementation and improves efficiency by eliminating the need for a current sense resistor. The wide programmable switching frequency range of 100kHz to 700kHz allows the use of small surface mount inductors and capacitors. The device also provides external frequency synchronization making it an ideal choice for DC-DC converter applications.

File format: PDF Size:449 KB

ISL6405 is a highly integrated voltage regulator and interface IC, specifically designed for supplying power and control signals from advanced satellite set-top box (STB) modules to the low noise blocks (LNBs) of two antenna ports. The device is comprised of two independent current-mode boost PWMs and two low-noise linear regulators along with the circuitry required for 22kHz tone generation, modulation and I2C device interface. The device makes the total LNB supply design simple, efficient and compact with low external component count.

File format: PDF Size:329 KB

This product is a high-performance 16-bit quadrature numerically controlled oscillator (NCO16) that simplifies applications requiring frequency and phase agility such as frequency-hopped modems, PSK modems, spread spectrum communications, and precision signal generators.

File format: PDF Size:55 KB

HS-26CT32RH-T is a Quad Differential Line Receiver produced by Intersil. It is of QML Class T and has been fully tested. It can work normally under a total dose of 100kRAD. The product is designed for digital data transmission over balanced lines and meets the requirements of EIA Standard RS-422. The Radiation Hardened CMOS processing assures low power consumption, high speed, and reliable operation in the most severe radiation environments.

File format: PDF Size:45 KB

The HIN232-HIN241 family is a +5V powered RS-232 transmitter/receiver interface circuit that meets all EIA RS-232E and V.28 specifications, particularly suitable for applications where ±12V is not available. They require a single +5V power supply (except HIN239) and feature onboard charge pump voltage converters that generate +10V and -10V supplies from the 5V supply. The family of devices offers a wide variety of RS-232 transmitter/receiver combinations to accommodate various applications (see Selection Table). The drivers feature true TTL/CMOS input compatibility, slew-rate-limited output, and 300Ω power-off source impedance. The receivers can handle up to ±30V and have a 3kΩ to 7kΩ input impedance. The receivers also feature hysteresis to greatly improve noise rejection.

File format: PDF Size:580 KB

HI5741 14-bit, 100MSPS, High Speed D/A Converter

File format: PDF Size:283 KB

File format: PDF Size:0 KB

The HFA1150 is a high performance, wideband, fast settling op amp built with Intersil's proprietary complementary bipolar UHF-1 process. The current feedback architecture delivers superb bandwidth even at very high gains (>300MHz at AV = 10), and the low distortion and excellent video parameters make this amplifier ideal for communication and professional video applications. Though specified for ±5V operation, the HFA1150 operates with single supply voltages as low as 4.5V, and requires only 3.4mA of Icc in 5V applications (see Application Information section, and Application Note AN9891). For a lower power amplifier in a SOT-23 package, please refer to the HFA1155 data sheet.

File format: PDF Size:263 KB

This family will also be available in single, dual, and triple versions, with 200MHz, 400MHz, and 750MHz versions. These are all available in single, dual, and triple versions. Both families operate on single 5V or ±5V supplies from minimum supply current. EL5x02 also features an output enable function, which can be used to put the output in to a high-impedance mode. This enables the outputs of multiple amplifiers to be tied together for use in multiplexing applications.

File format: PDF Size:1627 KB

The X9118 is a chip that integrates a single digitally controlled potentiometer (XDCP) and has low power consumption and dual power supply functions. It includes 1024 resistor tap points, and the position of the wiper can be controlled by the user through a 2-wire bus interface. The chip can be used as a three-terminal potentiometer or a two-terminal variable resistor in a wide range of applications such as control, parameter adjustment, and signal processing.

File format: PDF Size:342 KB

X5168, X5169 are CPU supervisors produced by Intersil. They integrate low voltage detection and reset control, power supply voltage monitoring, serial EEPROM, etc., reducing system cost, reducing board space requirements, and increasing reliability.

File format: PDF Size:358 KB

The document is the product manual of Intersil X28C010 5 Volt, Byte Alterable EEPROM.

File format: PDF Size:609 KB

HIP6017 Advanced PWM and Dual Linear Power Control for High-Performance Microprocessor and Computer Applications

File format: PDF Size:139 KB

The X4643/5 is an integrated circuit produced by Intersil, which has an optional watchdog timer, power supply voltage monitor and 64K EEPROM memory function.

File format: PDF Size:316 KB

X40010/11/14/15 is a voltage monitor chip produced by Intersil. It has dual voltage detection and reset signal generation functions, low power consumption, and is suitable for industrial, computer and other fields.

File format: PDF Size:358 KB

BCW60, BCX70 are NPN silicon AF transistors for AF input stages and driver applications. Features include high current gain, low collector-emitter saturation voltage and low noise between 30 Hz and 15 kHz. BCW60 and BCW61 are complementary types, with BCW60 being NPN and BCW61 being PNP.

File format: PDF Size:231 KB

File format: PDF Size:410 KB